We are winding up our kitchen make over, and one of the last big projects was adding a tile back splash. I envisioned a sea glass look that would tie into our recycled glass counter tops. I ordered samples from a few tile places, all in shades of blue & green. It was easy for me to decide that I loved the 3×6″ glass subway tile from Tile Bar the most. I debated a few different shades, but really fell for the frosted glass look. So, I decided to go with the Loft Seafoam 3X6 Frosted Glass Tile from Tile Bar. We feel so lucky that Tile Bar wanted to partner with us and offered to send us the tile.
How to Hang a Tile Bar Glass Subway Tile Kitchen Backsplash
Hanging a glass tile back splash is really easy, but just a little bit time consuming. We started by watching a few videos to get the best tips ourselves and here’s one that’s good for glass subway tiles.
What you need:
- Newspaper or plastic
- Painters tape
- Mortar spreader
- Bucket + water
- Mixing drill attachment
- Wet saw
- Tile spacers (we used 1/4″)
- Tile for your square footage + 10% extra just in case
- Unsanded grout
- Grout float
What you do:
First, prep your work area.
- Remove everything from the counter tops.
- Pull out the stove or anything blocking your wall.
- Use painters tape + newspaper to cover all of your surfaces. You will make a mess!
- If your wall is painted, you can score the paint. We used a scoring tool but any sharp edge would do. (optional)
- Use a drill to drill screws into the studs. This will hold the drywall extra-securely to the wall under the weight of the tile. (optional)
- Turn off power to your outlets
Next, you will want to mortar. This is the glue that will hold the tile to the wall.
- Mix your mortar according to the instructions on the package. This should require mixing the powder with water using a mixing attachment to your drill and you’ll mix a few minutes, wait a few minutes, then mix a couple of more minutes.
- Using your mortar spreader, grab some globs of mixed mortar and spread it on a small section of wall. Spread enough for what you can do in 15 minutes or so.
- Use a wet saw to cut your tiles in the patterns you need, being sure you’ve drawn the appropriate cuts for around your outlets.
- Place your tiles in the pattern you choose (we chose a 50-50 split on each level) and place your tile spacers in between.
- One tip for areas not up against a counter is to drill a piece of wood level across the wall for the tiles to rest on.
- Let your tiles sit for 24 hours to solidify.
The next step is to grout. If you have glass tile, you want unsanded grout – the sand can scratch the tile!
- After waiting 24 hours, mix your grout according to the package instructions. It should be roughly the same as the mortar mix.
- Spread the grout all over your beautiful new tiles. Yes, it’s sad. I was terrified when I started spreading this gross stuff all over the gorgeous tiles I had just laid yesterday. Sigh. But it’s ok. Spread the grout in small areas and try to go over all the lines from multiple directions to try to get the grout into the lines as best as possible.
- Use the edge of the grout float to scrape flat across the surface of your tile to wipe some of it away as best as possible.
- Once you’re completely done grouting, use a sponge, dipped in water and wrung out so it’s only a little damp, to wipe your tiles clean. Try to wipe in just one direction so you aren’t spreading the grout back over the areas you just wiped. Continuously clean off your sponge and do this over and over again. Once it looks pretty clean, let everything dry for 24 hours.
- Next you want to de-haze the tile to remove the lingering film of grout. We used de-haze gloves. You can also use the spray and a soft cloth.
The final step is to seal your grout.
- Apply the sealant to your grout. Let sit according to the directions on your packaging. This will help protect the grout from being stained.
- Then caulk the bottom and top of the tile to the wall and counter so it looks like a smooth transition.
In the end, it looks AMAZING!
We don’t have too much kitchen work left. I need to take down the cabinet over the fridge & paint and reconfigure it a little bit, but other than that it is just tweaks. I am planning to do a great big reveal when it is totally done – and I can’t wait to share it with you!
Thank you to Tile Bar for providing the tile for our back splash. All opinions are true & my own. Thanks for supporting the brands that make Charleston Crafted possible.
This post was last updated on