Skip to Content

How to Mount a Barn Door Using TC Bunny Hardware from Amazon

Yesterday we shared with you how to build a rustic barn door like the one we constructed to go between our master bedroom and bathroom. Building the door was super easy, but when it came to mounting it, that was a different story.

We ordered the TCBunny Sliding Door Hardware from Amazon and had a lot of problems with it. Luckily, we are super crafty people we managed to work around them. Here’s how to mount a barn door and work around any problems you have with the TCBunny sliding door hardware.

Here is how we lock our barn door!

First off, we didn’t read the comments. That’s our own fault. We usually always read comments, but didn’t this time (it has four and and half stars!). Basically, anyone from America said that this product was the worst. That’s because the holes on the TCBunny system don’t line up with studs in American homes.

This causes it to be unstable. Luckily, TCBunny includes anchors for the screws. Unluckily, those anchors are the worst and do nothing. Just take a look at these instructions:

How to Mount a Barn Door - Charleston Crafted

How to Mount a Barn Door - Charleston Crafted

These instructions are of a lower quality than the pictures that IKEA gives you. These instructions skipped steps and didn’t label parts and went out of order. They were basically worthless. Unfortunately, I drilled five holes in my wall before I realized how crappy the system and anchors were.

So, backup plan. We went to Lowe’s and talked to them about whether or not we should try to use professional grade anchors, but the guy there highly voted against it.

He confirmed my other idea, which was to attached another piece of wood to the studs of the wall and attach the sliding door system to that piece of wood. Also, it would cover the big holes I just drilled.

How to Mount a Barn Door - Charleston Crafted

So, I got another 1″x6″ piece of pine and went through the same staining process that I just did for the door. The other option was to paint the wood the same color as the wall so it would blend in, but thinking that it would still be obvious if we did it that way, we decided to stain it to make it look purposeful. So, after the stain was dry, I used my stud finder and then used 3 1/2 inch wood screws to attach the board to the wall.

How to Mount a Barn Door - Charleston Crafted

Then, we were finally able to start using the TCBunny sliding door system. Keep in mind, I’m about to make up the names for most of these pieces because they don’t have real names.

So, first off, line up the rail bar on the board and mark your five holes. The rail is really heavy steel, so you’re going to want a friend to help.

How to Mount a Barn Door - Charleston Crafted

Then, attach the rail to the wall using the separator nubs and the long black wood screws. Start with the one in the middle, then do the next ones on each side.

These are tough because you have to put the screw through the rail before going through the nub, but you have to hold the whole thing up. Again, use a partner. You’ll need a ratchet set for this.

Try to screw it in a little bit and then move on to another before getting it all the way tight. Then it will be holding itself up.

How to Mount a Barn Door - Charleston Crafted

Once you have those first three up, PAUSE. There is a step at the very end of the instructions to add the bumpers, buuuuut in order to do that, we had to remove two of the nubs and slide the bumpers into place.

So, do yourself a favor and add those in between nubs 1 and 2 and nubs 4 and 5. You’ll need a really small allen wrench to tighten the bumpers.

How to Mount a Barn Door - Charleston Crafted

Now, you’re getting close. Attach the sliders to the top of your door using the black nuts and bolts. If you’ve done it all right, now’s the time to place the door up on the rail using the rail wheels.

How to Mount a Barn Door - Charleston Crafted

Your door should now be rolling freely, assuming you measured the proper height for the door. You’re almost done. The last step is to install the bottom guide.

If you haven’t noticed, your door is swinging back and forth from the top and needs something to hold it in place. This little guide requires a track to be cut into your door.

This is easy to do by running the bottom of your door twice across a table saw. Make sure to place the bottom guide in a spot that it will be in the door when it’s at both ends of the track.

How to Mount a Barn Door - Charleston Crafted

That’s it. This TCBunny sliding door hardware system comes with really bad instructions and extra parts that literally don’t mean anything, so don’t worry. But if you follow our hacks, you should be in a much better place.

Now we have a beautiful sliding barn door to close off our master bathroom from our master bedroom and it’s also an art piece on the wall when it’s open. It turned out perfect and looks super rustic. Plus, we did it all ourselves and can always be proud of that.

How to Mount a Barn Door - Charleston Crafted

Want more barn doors? Click here for all of our barn door content!

How to Mount a Barn Door - Charleston Crafted

I really hope these instructions for how to mount a barn door help you out!

Want more barn door goodness? We wrote an eBook all about Barn Doors – and you can get it for free!

 Charleston Crafted Logo heart
 Charleston Crafted Logo facebook
 Charleston Crafted Logo insta
 Charleston Crafted Logo pinterest
 Charleston Crafted Logo twitter
Can I use a barn door for a bathroom?
Yield: 1

How to Build and Mount a Barn Door

Prep Time: 2 hours
Active Time: 2 hours
Total Time: 4 hours
Difficulty: Medium
Estimated Cost: $100-250

Barn doors are trendy and fashionable and can add a rustic flair to your space. Here's how to build a barn door and how to mount a barn door.

Materials

  • Roughly nine 1x6 boards
  • Screws
  • Barn door hardware

Tools

  • Miter saw
  • Drill

Instructions

How to Build a Barn Door

  1. Measure the space you want to cover
  2. Design your door. Use two layers.
  3. For the back layer, use as many 1x6 boards as needed to cover the gap of your door.
  4. For the front layer, cut two 1x6 boards to span the width of your door space and attach at the top and bottom of the back layer. Then cut 1x6 boards to span the gap between those two boards vertically. Finally, cut a board to go diagonal from the top corner to the bottom corner.
  5. Use 1 1/4" screws to attach all the boards from the front layer to the back layer.
  6. Stain or paint your door to fit your decor.
  7. Add a pull for a door handle.

How to Mount a Barn Door

  1. Order barn door hardware. Different brands will differ slightly, but the idea is the same.
  2. Attach a 1x6 board to your wall in the studs if your doorway has a frame that you need to go past. If your doorway doesn't have a frame, you can mount your rail bar directly into the wall.
  3. Mount your rail bar.
  4. Add bumpers for the barn door rollers to hit where you want to door to stop on each end.
  5. Attach the rollers to the top of your door and hang the door on the rail bar.
  6. Add a bottom guide for your barn door so that it doesn't swing back and forth.

Recommended Products

As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases.

Did you make this project?

Please leave a comment on the blog or share a photo on Pinterest

Dave Winstanley

Thursday 1st of March 2018

Regarding the slot needed in the bottom of the door for the guide, you say "...This is easy to do by running the bottom of your door twice across a table saw." I'm not sure how that is easily accomplished. Can you explain further?

Sean

Thursday 1st of March 2018

Hey Dave. So basically what I mean is that we took the fully completed door and then stood it up on it's end. We set the table saw fence so that the blade would run right through the middle of the thickness of the door. Then we ran the door through the saw standing up, so the blade carved a notch right down the middle of the thickness of the door. Does that make sense? Another way to do it would be to run a palm router through that area instead. You just need to cut out a gap for the guide to go through.

Brad

Tuesday 24th of October 2017

Hi -- I have the same product, and the same problem with the screws not aligning with the studs. I like your solution (using the board stained the same as the door) BUT -- doesn't that make the door stick out further from the door/doorway/wall, because you have added the extra depth of the wood panel?? How did you account for this? Without the wood panel (ie. screwing straight into wall) my door will be perfectly close to the door frame.

Sean

Wednesday 25th of October 2017

Hey Brad. So yes, it would add extra depth. For me, that actually ended up being exactly what I needed because of the door frame that the barn door was going to cover. In my initial plans, I hadn't even taken that into consideration, so it turned out to be a blessing in disguise. For you, I'll say that you could probably go with a little thinner of a board to mount it on, or you could put up a faux frame around the door frame or inside of the barn door that would fill the gap that would be caused by the extra depth.

Tracy

Thursday 27th of July 2017

Hi Sean, thanks for the post on the instructions, mine came only in mm, no inches at all. I was able to figure out most everything with the help of YouTube. My issue is that the drilled holes in the mounting board seem to be too big, but after checking many sources 5/16" bit should be right. My package didn't come with anchors, although from what I've read, sounds like the would be not have been of much use. Any ideas? I've only put in two of the screws, thought I should quit, and get some advice.

Sean

Thursday 27th of July 2017

Hey Tracy! Yeah, I thought about using anchors as well, but considering how much weight they would be holding up, I didn't trust them. My suggestion would be to do what I did, adding a piece of wood to the wall and attaching that piece of wood to the studs in your wall. Then just mount your screws into the holes that are on the mounting board where you need them and don't have to worry about them lining up with the studs. Does that help?

Laurie Solheim

Thursday 6th of July 2017

Is your header a literal 1" thick or 3/4?

Sean

Thursday 6th of July 2017

It's a common 1 inch, but an actual 3/4 inch.

Thomas

Tuesday 20th of June 2017

Would like to know how to measure where to install the rollers on the door. The instructions doesn't give how high above the door the rollers should be or how far from the edge of the door.

Sean

Tuesday 20th of June 2017

Hey Thomas, so the main thing to consider when installing the rollers on the door is that the two bolts fit well onto the door and aren't near the edge. If the top bolt is too close to the edge it might break out. Based on the board that I used, the rollers fit perfectly lined up with the bottom of the board. You can have the rollers closer to the top of the door, just make sure there is enough clearance for the bar to go between the rollers and the top of the door.

Comments are closed.
Skip to Instructions